Xerox WorkCentre C2424 DADF Error Codes and Replacement

If your Workcentre C2424 is getting a 39,010.8,.40 39,012.41, 39,013.42, or 39,014.43 you most likely need to replace the DADF assembly (Document feeder). This video will show you how.

Xerox WorkCentre C2424 DADF Assembly:  Part# - 004K07270.    

Read More..

Secret Codes for Android Phone

While I was browsing the web, I found some interesting codes for Android phone which can enable/disable lots of hidden settings and show many useful information about the phone. These hidden codes can be used in any Google Android mobile phone to access things which are not accessible by default.

    *#*#4636#*#*

This code can be used to get some interesting information about your phone and battery. It shows following 4 menus on screen:

    * Phone information
    * Battery information
    * Battery history
    * Usage statistics

   *#*#7780#*#*

This code can be used for a factory data reset. Itll remove:

    * Google account settings stored in your phone
    * System and application data and settings
    * Downloaded applications

It will NOT remove:

    * Current system software and bundled applications
    * SD card files e.g. photos, music files, etc.

PS: Once you give this code, you get a prompt screen asking you to click on "Reset phone" button. So you get a chance to cancel your operation.

    *2767*3855#

This code is used for factory format. Itll remove all files and settings including the internal memory storage. Itll also reinstall the phone firmware.
PS: Once you give this code, there is no way to cancel the operation unless you remove the battery from the phone.

    *#*#34971539#*#*

This code is used to get information about phone camera. It shows following 4 menus:

    * Update camera firmware in image (Dont try this option)
    * Update camera firmware in SD card
    * Get camera firmware version
    * Get firmware update count

WARNING: Never use the first option otherwise your phone camera will stop working and youll need to take your phone to service center to reinstall camera firmware.

    *#*#7594#*#*

This one is my favorite one. This code can be used to change the "End Call / Power" button action in your phone. Be default, if you long press the button, it shows a screen asking you to select any option from Silent mode, Airplane mode and Power off.
You can change this action using this code. You can enable direct power off on this button so you dont need to waste your time in selecting the option.

    *#*#273283*255*663282*#*#*

This code opens a File copy screen where you can backup your media files e.g. Images, Sound, Video and Voice memo.

    *#*#197328640#*#*

This code can be used to enter into Service mode. You can run various tests and change settings in the service mode.

WLAN, GPS and Bluetooth Test Codes:

    *#*#232339#*#*

    *#*#526#*#*

    *#*#528#*#*

WLAN test (Use "Menu" button to start various tests)

    *#*#232338#*#*     - Shows WiFi MAC address
    *#*#1472365#*#*  - GPS test
    *#*#1575#*#*          - Another GPS test
    *#*#232331#*#*  - Bluetooth test
    *#*#232337#*#  - Shows Bluetooth device address

Launch GTalk Service Monitor :

    *#*#8255#*#*

Codes to get Firmware version information:

  *#*#4986*2650468#*#* -PDA, Phone, H/W, RFCallDate
   *#*#1234#*#*     - PDA and Phone
   *#*#1111#*#*       - FTA SW Version
   *#*#2222#*#*   - FTA HW Version
   *#*#44336#*#* - PDA, Phone, CSC, Build Time, Changelist number

Codes to launch various Factory Tests:

    *#*#0283#*#* - Packet Loopback
    *#*#0*#*#* - LCD test
    *#*#0673#*#* OR *#*#0289#*#* - Melody test
    *#*#0842#*#* - Device test (Vibration test and BackLight test)
    *#*#2663#*#* - Touch screen version
    *#*#2664#*#* - Touch screen test
    *#*#0588#*#* - Proximity sensor test
    *#*#3264#*#* - RAM version

Source[Nexusoneforum]

Read More..

Canon mp150 reset codes

MP150/MP160 ERROR CODE
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full

E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

How to clear E27 Code

• With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
• When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
• When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
• When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)

• Turn off the printer.( it must be turn off) then turn it on again.

Read More..

E061 E100 Error Codes iR6570 Series iR5075 Series

Symptom

* E061-0001 (Potential ON)
* E061-0002 (Potential OFF)
* E100-0001
* E227-0004
Cause
* The pin is broken on the Primary Fan 2 Duct. The Laser Shutter is activated by the pin on the Primary Fan Duct Assembly. The linkage is pinched not allowing the laser shutter to be fully actuated (may also indicate E227-0004). Faulty Laser Scanner Assembly.
* Defective DC Controller PCB Assembly.

Action

1. Check the shutter operation and the pin on the Primary Fan Duct Assembly. If the
pin is broken replace the Primary Fan 2 Duct (iR6570 : FC6-3540-000 / iR5075
FL2-5834-000) or the Primary Fan Duct Assembly (iR6570 : FM2-3074-000 / iR5075
FM2-9694-000). If the Laser Scanner Assembly (iR6570 : FM2-3670-000 / iR5075
FM2-9832-000) has been replaced and error codes E100-0001/ E227-0004 are
intermittently indicated, proceed to the next step.
2. Remove the Primary Fan Duct Assembly (this assembly has a pin on it
that activates the laser shutter).
3. Remove and reinstall the Laser Scanner Assembly.
4. Install the Primary Fan Duct Assembly. This should free the linkage
allowing the laser shutter to be fully actuated.
5. Finally a DC Con clear resolved both of the intermittent issues (E100-0001/
E227-0004)

Blank Image or Dark Fogging Image (Including Blank Areas) and E061-0001 / E061-0002 Errors Occur : iR6570 Series
Approved

Symptom

* Blank copies,Dark fogging
* E061-0001 and E061-0002

Action

When the above error code/image problems are experienced, perform the following:

1. Check the potential sensor wiring harness for any damage. This is caused by the harness being trapped between the hopper assembly and the cable tie head.
2. If the cable is damaged repair or replace as necessary.
3. Reposition the head of the cable ties on the cable guide in a downward position.
4. Input "1" under Service Mode > COPIER > FUNCTION > DPC > DPC, press the OK key and switch the Main power off and on so as to forcibly execute the Potential Control.

Read More..

Printer Xerox Phaser 7700 error codes

• Error Code 10: Laser Unit failure

Solution: Remove Rear Cover , Disconnect P400 , and P401 on the Engine Control Board. Inspect both connectors to determine they are fully engaged as a unit. Re-engage, if necessary.
Carefully reinsert the plugs into their joint socket and FIRMLY seat them.

If the problem persists, replace the Laser Unit ,and , or , the Engine Control Board (116-1144-00).

• Error Code 11: Laser Unit Polygon Motor Failure

Solution: Remove Rear Cover , Disconnect P400 , on the Engine Control Board. Inspect both connectors to determine they are fully engaged as a unit. Re-engage, if necessary.
Carefully reinsert the plugs into their joint socket and FIRMLY seat them. Replace the Laser Unit , If the problem persists, replace the Engine Control Board (116-1144-00).

• Error Code 12, 13 ,14 and 15: ATC Sensor Failure

Solution: Remove the Rear Cover , and Rear Shield , Measure the voltage at P534-5 on the Engine Control Board. Does the voltage measure between +1 VDC and +3 VDC ?
If yes: Replace the Engine Control Board (116-1144-00).

If no: Replace the Developer Housing Assembly

Replace the Engine Control Board , Replace the Developer Housing Assembly
If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the NVRAM Access.Clear Tech Rep Fault / Clear &<09-380 ~ 09-383> is run.

• Error Code 30: Accumulator Belt home position took too long

Solution: Ensure the Accumulator Belt shipping restraints have been removed. Enter Service Diagnostics Mode; Run the “Clear Tech Rep Fault”.
Lower the Main Release Lever and return to the upright position to reestablish electrical connections to the belt. Open the RH Door and defeat the interlock switch.
Look for rotation of the Accumulator Belt during the following test.
Enter Adjustments / Calibrations menu. Run the “Belt Edge Learn” test.
If the problem persists, replace the Engine Control Board (116-1144-00).

• Error Code 40: Fuser Main lamp failure

Solution: Switch printer power OFF. Remove the Fuser Assembly.
Warning Fuser may be very hot. Use extreme caution to prevent burns. Measure the resistance between the Fuser Assembly connector P600-4 and P600-6. Does the resistance measure between 20K and 100K ohms ?
If no: Replace the Fuser Assembly.
If yes:  Reinstall Fuser, Remove the Rear Cover, Rear Shield and the Rear Shield Bracket , Measure the resistance between P404A-1. Does the resistance measure between 20K and 100K ohms?
If no: Repair or replace the wiring harness between the Engine Control Board and the Fuser.
Replace the Engine Control Board (116-1144-00).

• Error Code 54: Fan failure

Solution: Enter Service Diagnostics Mode. Run the “Fuser Fan” test. Does the Fuser Fan operate?

If yes: replace the low voltage power supply fan.

If no: replace the fuser fan.

• Error Code 60: Drum motor failure

Solution: Enter Service Diagnostics Mode and run the “Print Cartridge Motor” test. Does the motor run?
If yes: Replace the Engine Control Board
If no: Remove the Rear Cover , the Rear Cover Shield , Measure the voltage at the Print Engine Controller Interface Board P407-4(+) and frame ground. Is the voltage +5 VDC ?
If no: Replace the Engine Control Board (116-1144-00).

Read More..

Canon IR1600 error codes

 

• E000: The main thermistor reading does not reach 40ºC 14 sec after the fixing heater goes ON. (fixing low temperature error)
• E001: The main thermistor reading reaches 220ºC or higher.
• E002: A start-up fault is detected under any of the following conditions of the main thermistor
• E003: After the end of the WAIT period, the main thermistor reading is 100ºC or lower. In standby, the sub thermistor reading is 50ºC or lower.
• E004: At time of initialization, the ZEROXI signal of the power supply is not detected. During temperature control, the ZEROXI signal does not arrive for 3 sec continuously. A short circuit is detected in the triac
• E010: A specific revolution is not detected from the main motor rotation detection signal.
• E100: When the scanner motor is started up, the BD input signal does not arrive within a specific period of time.
• When the scanner motor is started up, the motor rotation is too fast, and fails to reach a specific revolution within 20 sec at time of deceleration. While the scanner motor is rotating at a specific speed, the BD input signal cycle is not within a specific range (±2%) for an equivalent of 10 mm (print distance). While the scanner motor is rotating at a specific speed, the BD input signal cycle is not as indicated (±2%).During the WMUPR period after the power switch has been turned on or the front cover/left cover has been opened/closed, the drum unit is absent.
• E719: The communication between the card reader and the image processor PCB is disrupted.
• E805: After the heat discharge fan drive signal is generated, the fan lock detection signal does not arrive for a specific period of time.
• E500: An error has occurred in the communication between the machine and the finisher twice continuously.
• E514: The stack delivery belt does not reach home position when the stack handling motor (M2) is driven for a specific time (CW; if the same condition occurs during stack delivery, a jam will be identified).
• E530: The rear aligning plate does not reach home position when the rear alignment motor (M4) has been driven for a specific time.The rear aligning plate does not reach home position when the rear alignment motor (M4) has been driven for a specific time.
• E531: The stapler does not leave the stapling home position sensor (S13) within 0.5 sec after the stapler motor (M6) is rotated CW.The stapler does to return to the home position sensor (S13) within 0.5 sec after the stapler motor (M6) is driven CW and, in addition, it does not return to the sensor within 0.5 sec after the motor is driven CCW thereafter.
• E537: The front aligning plate does not reach home position when the front aligning motor (M3) is driven for a specific time.The front aligning plate does not leave home position when the front alignment motor (M3) is driven for a specific time.
• E551: The delivery fan rotation signal (FNALCOK) does not arrive within 1 sec when the heat discharge fan drive signal (FANON) is sent.
• E577: The return roller does not reach home position when the delivery motor (M1) is driven for a specific time. (If the same condition is detected while alignment takes place in the direction of feed, a jam will be identified.)
• E580: The stack tray upper limit sensor (S1) goes ON while the stack tray up/ down motor (M5) is in operation.The clock signal of the stack tray up/down clock sensor (S9) is not detected 15 times or more within 0.8 sec while the stack tray up/down motor (M5) is in operation.It does not reach the stack tray paper height sensor (S10) 2 sec after the stack tray up/down motor (M5) rotates for ascent.It does not leave the stack tray power height sensor (S10) 2 sec after the stack tray up/down motor (M5) starts to rotate for descent.
• E585: The stack retaining lever does not reach home position when the stack handling motor (M2) has been driven for a specific time (at the start of motor CCW rotation). (If the same condition is detected during stack delivery, a jam will be identified.)

Read More..